9 Ball Stop Shot: How to Stop the Cue Ball Dead for Easy Position

Quick answer: A 9 ball stop shot is a straight in shot where the cue ball stops dead at the spot where it hits the object ball. To do it, hit the cue ball just below center so it slides with no spin at the moment of contact. The longer the shot, the lower you hit or the firmer you stroke, because the backspin needs to last until contact. In 9 ball, the stop shot gives you exact cue ball control on straight shots and helps you avoid scratches.

9 ball stop shot 9 Ball Stop Shot: How to Stop the Cue Ball Dead for Easy Position
On a straight in shot, a stop shot leaves the cue ball right where the object ball was.

The stop shot is one of the first cue ball skills every player should learn. It is simple, but it teaches you how spin and speed work together.

How the Stop Shot Works

When the cue ball rolls into an object ball straight on, it keeps rolling forward. When it slides with no spin, it transfers its motion to the object ball and stops. A stop shot is all about making the cue ball slide at contact. To do that, you hit below center so backspin cancels the natural roll right as the cue ball reaches the object ball.

How to Hit a 9 Ball Stop Shot

  1. Set up straight in. The cue ball, object ball, and pocket are in a line.
  2. Hit just below center. On short shots, a little below center is enough.
  3. Use a smooth, firm stroke. Too soft and the cue ball starts rolling before contact.
  4. Adjust for distance. For longer shots, hit a bit lower or a bit firmer.
  5. Follow through. Do not stop your cue at the ball.

Stop Shot vs Stun Shot vs Draw

Shot What happens at contact Result on a straight shot
Stop shot Cue ball slides, no spin Cue ball stops dead
Stun shot Cue ball slides on a cut Cue ball goes along the tangent line
Draw shot Cue ball still has backspin Cue ball comes back. See 9 ball cue ball control.

A stop shot is really a stun shot on a straight in shot.

When to Use a Stop Shot in 9 Ball

Why Speed Matters

Speed and tip height work together. If you hit low but very soft, the backspin wears off and the cue ball rolls through. If you hit low and very hard, the backspin is still there and the cue ball draws back. The sweet spot is a medium speed that keeps the cue ball sliding right at contact. Practice is the only way to learn it on your table.

Common Mistakes

Stop Shot Drills

Drill 1: The ladder. Place the object ball one diamond from a corner pocket, straight in. Start with the cue ball one diamond away. Stop the cue ball. Move it back one diamond each time.

Drill 2: Stop on the spot. Before you shoot, note which diamond the object ball lines up with. Try to stop the cue ball right on that line.

Drill 3: Stop, then roll, then draw. From the same setup, hit a stop, then a follow, then a draw. This shows you how small changes in tip height change the result.

For more practice ideas, see how to practice 9 ball alone.

The Bottom Line

The stop shot is simple, but it is a key building block. Once you can stop the cue ball at any distance, you can start to control it on cut shots too. That control is what turns makes into run outs in 9 ball.

Keep Reading on This Site

Frequently Asked Questions

What is a stop shot in 9 ball?

It is a straight in shot where the cue ball stops dead at the spot where it hits the object ball.

Where do I hit the cue ball for a stop shot?

Hit just below center. On longer shots, hit a little lower or a little firmer.

Why does my cue ball roll forward instead of stopping?

The backspin wore off before contact. Try a slightly lower hit or a little more speed.

Why does my cue ball draw back on a stop shot?

You likely hit too low or too hard for the distance. Ease up a bit.

Is a stop shot the same as a stun shot?

A stop shot is a stun shot on a straight in shot. On a cut, a stun shot sends the cue ball along the tangent line.